Design Your Own Crown – Make your own crown for coronation celebrations or for your own royal event! This beautiful medieval crown will outshine the competition, but is surprisingly quick and easy to make.
This version, modeled after the solid gold St. Edward’s crown of the British monarchy, is slightly cheaper and much less heavy on the head. The Crown of Saint Edward is considered the official coronation crown, and it is in which Queen Elizabeth II was crowned; making it the perfect model for our anniversary crown and coronation crafts.
Design Your Own Crown
With street parties for weddings and royal anniversaries, I have now made quite a few of these coronation crowns and can whip one out in about ten minutes. With a little practice you can make enough for an entire neighborhood in no time. A word of warning though. While they are not difficult to do, there are some parts that are a little tricky. My eight year old could handle them, but I think they would be difficult for younger children.
Color Your Own Birthday Crown
This post uses affiliate links, which means I receive a small commission when you click on a link and make a purchase. You can get more information on my ‘
2. Glue the two ends of the longer gold card strip together to form a headband or circle. This is the base of your crown, so make sure it fits you before gluing it in!
I’ve found that about 60cm is a good base size for most people, but see if it works for you – it may be too big for small children, but too small for some adults…
I used double-sided tape to make these coronation wreaths, but you can also use regular tape or glue.
Back To School Crowns For Kindergarten (first Week Of School)
3. Take one of the back piece strips (the black/base card) and glue one end to the inside of the circle.
Make sure you place it at the bottom of the circle (but with the back strip facing up), as shown in the image. You don’t want it to stick across the width of the circle because you will be gluing the trim and bow strips over it.
Attach the other end of the backing strip to the other side of the circle. Then do the same with the remaining dividing strip, but at a right angle to the first, so that the two strips cross in the middle.
This is the inner support. Later, cover it with tissue paper and attach the bows to it in the center.
King’s Crown Coloring Book · Creative Fabrica
Try your crown again at this point to ensure it still fits properly. The inner support should sit on or just above the head like a cap.
Before continuing, make a hole in the center of these support strips, at the midpoint where the two strips intersect.
4. Cut one end of each of your bow strips into a rounded point. Leave the other end flat.
Attach one of the bow strips to the front of the wreath and one to the back. To secure them in place, glue the flat end of these strips about halfway down the inside of the circle. Make sure they are at the same height as you want them all to be the same.
Make Your Own Crown Design On Canva Canva Frame Bundle Easy Drag And Drop Digital Sublimation Png King Queen Prince Princess Crowns
Repeat with the remaining bow strips, distributing them evenly around the circle. Somewhere between four (like the original St. Edward’s Wreath) and six strips looks best.
Make a hole in the top of each strip. Try again to place them at the same height and position on each strip so that they are all the same.
5. Now it’s time to cover the inner back strips by gluing the tissue paper or crepe leaves to the inside of the circle. Do this by gluing the long, flat edge around the circle, between the support cap and where you attached the arch strips, so that it covers the supports but doesn’t get in the way of the arches.
You should find that each petal covers just over a quarter of the circumference of the corolla and that they overlap perfectly. So it works best if you attach the side leaves first and the front and back last, so that they are on top.
Tinksky Birthday Hat Crowns Party Kids Tiara Hats Kit Paper Gold Make Crafts Baby Own Your Craft King Caps Girl Children Diy
And finally, insert a sharp pencil through the tissue paper, through the center hole you made earlier, where the support strips intersect.
6. Cut out a shape to use as a decoration for the center of your wreath, where the bows are. I used a cross shape, similar to that of the royal crown of St. Edward (a cros-pattée, if you want to get all technical).
You can download or copy a template for my cross (along with the lining petals) from my printable page, although you don’t have to be too precise.
Cut out two of these shapes making sure there is a tab at the bottom (as per my template).
Crown Tattoo Idea For Shoulder
Glue the two shapes together (not the tabs!). Then fold the tabs so that the combined shape stays upright.
7. To complete the structure of your crown, insert the cotter pin (or brad) through the top of the hole you just made in the tab of the top ornament so that the pin hangs down.
Then, with the pin attached to the top, insert it through the holes at the end of each of the bow strips and connect them all at the tip.
Now gently pull the tie strips down so they curve towards the center, insert the cotter pin through the hole in the tissue paper/crepe and the support strips in the center of the crown.
S020-2e) Princess Tiara Crown Monogram Name Big Little Sister Cousin
8. To make the purple crown, glue the remaining four decorations to the base of each bow. The real St. Edward wreath also has fleur de lis between the crosses around the circle, but we didn’t have room in our wreath.
You can of course add decorations to the ends of the bows if you make six instead of four, but we thought it was a bit too busy. Instead of crosses you can also use other shapes, such as fleur de lis.
9. Your coronation crown is fine to wear as is, but since the real St. Edward’s crown is decorated with 444 different gemstones, you might want to add a few to your crown too!
I made our coronation wreath from thin gold cardstock and tissue paper, but you could just as easily use sugar paper. I actually made a test version using regular printer/copier paper, which also worked well, although it is obviously a little less robust than the card versions.
Design Your Own Princess Crown
This paper version didn’t need all that tape until it was weighed down by all the jewelry that an enthusiastic eight-year-old decided was necessary…
Looking for more fun things to do and do with the kids? Check out these great rhubarb and wren activities! Make your little princess feel like royalty with these DIY princess crowns! These crowns are easy to make and perfect for a princess party.
My daughter loves all things princess. Of course, I’ve encouraged her love of princesses from day one, partly because I love them too. My sister and I grew up watching classic Disney princess movies, and you can never get over it!
Since we’re big princess fans, I wanted to make a simple craft that brings the princess magic home. These DIY princess crowns are just that! A template is used to make creating the crown shape a breeze. After you cut out the crown, add a few gemstones for a little sparkle and any other embellishments you want. Read the tutorial to learn how to recreate this princess crown house at home!
Creative Ideas From Creative Minds: Make Your Own Crown
The easy-to-print template makes this princess crown craft easy for anyone to make! This is what you need:
Need inspiration for these wreaths? You never need a reason to make your own DIY princess crowns. But if you’re looking for the perfect time to develop this craft, this list might inspire you!
The great thing about these DIY princess crowns is that the decoration possibilities are endless. If you have a wealth of craft supplies at home, feel free to bring a few more options to the table. Here are some more ideas for your princess crown decorations:
Throwing a princess party? Do you have a princess-obsessed little one at home? Complete your festivities with these princess activities!